Gardco Adjustable Micrometer "MICROM II" Film Applicator
With New Stainless Steel Blade
(patent pending)
No springs to break, rust or get clogged.
Detachable Blade makes cleaning easy.
Enhanced accuracy.
Ergonomic Design facilitates fast, accurate draw downs.
THE ADJUSTABLE MICROM FILM APPLICATOR CONSISTS OF THE FOLLOWING:
A finely machined stainless steel knife-blade fitted into slots in the end section that allows vertical adjustment of the blade.
Two finely-made micrometer barrels that can be easily set so that gate clearances can be adjusted from 0 to 0.250" in increments of 1 mil (.001") with resolution to 1/2 mil (.0005"). Thimbles and barrels of the micrometers are dull chrome.
A special clear anodized aluminum frame with two end sections that provide a large paint well. The end sections also serve as ergonomic operator hand grips when drawing down wet films.
Rare earth magnets hold the stainless steel blade firmly in place allowing for quick, easy detach and cleaning.
Replacement blades are easy to install and calibrate.
For information on laying down wet films of coating materials refer to ASTM Specification D 823, Producing Films of Uniform Thickness of Paint, Varnish, Lacquer and Related Products on Test Panels.
OPERATION
Place applicator at upper end of test panel. Pour coating directly in front of the knife-blade. Draw applicator slowly toward lower end of panel at a uniform rate of 10 to 12 inches (250- 300mm) per second. Clean applicator immediately after use. Caution: Do not wet or submerse micrometer heads.
CALIBRATION
Before use, check the zero settings of the micrometers. Place applicator on a polished granite block or alternatively plate- glass of suitable size. Set micrometers at zero. When the applicator is placed between the observer and a bright light, the blade should touch the glass from end to end without the sideplate being elevated. The zero point should check within ± 0.0005". If it does not, and settings are required, simply set the micrometers to zero, loosen the mike clamp set screws, press the knife-blade down on the glass plate, press down the micrometers until barrels are seated against the blade and then tighten the clamps.
available items
Catalog Number
Path Width
Overall Width
AP-99500201
2"
2-1/2"
AP-99500301
3"
3-1/2"
AP-99500401
4"
4-1/2"
AP-99500501
5"
5-1/2"
AP-99500601
6"
6-1/2"
AP-99500701
7"
7-1/2"
AP-99500801
8"
8-1/2"
AP-99500901
9"
9-1/2"
AP-99501001
10"
10-1/2"
AP-99501101
11"
11-1/2"
AP-99501201
12"
12-1/2"
AP-99501301
13"
13-1/2"
AP-99501601
16"
16-1/2"
Note: Items in Bold Red scheduled for future production, all others (except as indicated below as "Special Order") in stock.
AP-99501401
14"
14-1/2"
AP-99501501
15"
15-1/2"
AP-99501701
17"
17-1/2"
AP-99501801
18"
18-1/2"
AP-99501901
19"
19-1/2"
AP-99502001
20"
20-1/2"
AP-99502101
21"
21-1/2"
AP-99502201
22"
22-1/2"
Equivalent metric versions of all of the above models are available. A 6-inch applicator, for example, would become a 15.2mm path width blade, adjusting in 0.01mm increments to 13mm maximum opening. For locking micrometer models, add $100.00.
이 상품에 적용된 할인내역입니다
