¿É¼Ç ¼±ÅÃ(1.53m*1´Ü) 1.53m (Bottom Section with Valve)
ea/1
170,000¿ø
17,000¿ø
C14516WA
¿É¼Ç ¼±ÅÃ(0.8M*1´Ü)*0.80m (Top Section with Rope)
ea/1
150,000¿ø
15,000¿ø
C09249WA
¿É¼Ç ¼±Åà Case for Sampler
ea/1
125,000¿ø
12,500¿ø
B01291WA
¿É¼Ç ¼±Åà Cleaning Brush
ea/1
°¡°Ý¹®ÀÇ
°¡°Ý¹®ÀÇ
¡á ¿ëµµ(Applications) * The material is very rigid, minimizing bending of the unit when it is full of water or other liquids * Do not use for sampling ethanol or ethanol blended fuel. * Use Nasco fuel sampler (B01477). * The Sludge Judge¢ç is designed to take accurate readings of settleable solids, 5% or less, in a variety of liquids, to any depth.
¡áƯ¡ (Features ) * The Sludge Judge¢ç - 15 ft. (4.60 m): C09247WA * It is ideal for sewage treatment plants, chemical plants, and food processing facilities - anywhere that accurate sample levels of settleable solids in noncaustic materials are needed. * The unit holds approximately 3 oz. per foot (89 ml per 0.31 m). * The Sludge Judge¢ç comes in 5 ft. (1.53 m) sections of 3/4" (1.90 cm) plastic pipe with screw-type connectors. * The top section includes a nylon rope for raising and lowering the sampler. * Individual sections can be combined as required to achieve the length needed. * Do not use in liquids over 165¡Æ F (74¡Æ C). * Sludge Judge¢ç is not autoclavable. * A convenient cotton canvas carrying case that holds four sections, a cleaning brush, cleaning rod, and cotton strips are available.
* The Sludge Judge¢ç II - Large Capacity: B01355WA * Do NOT use for sampling ethanol or ethanol blended fuel. * Use Nasco fuel sampler (B01477). * The Sludge Judge¢ç II is made from a 1-1/4" (3.18 cm) outside diameter plastic tubing resulting in double the capacity and a very rigid unit when assembled. * Designed for sampling 5% or less solids. * It holds 6 oz. per foot (178 ml per .31 m) and can be assembled according to the requirements of the job. * Add or subtract sections as needed, and the 1-ft. (.31 m) markers on the tubing will help identify the amount of sludge in the tank. * The unit is made up of three 5-ft. (1.53 m) sections (top, extension, bottom) or individual sections can be combined as required. * The Sludge Judge¢ç is not autoclavable.
¡á ±Ô°Ý(Specifications) To use: * Slowly lower the Sludge Judge¢ç to the bottom of the tank. * The float valve opens, allowing materials to flow in. * When the bottom has been reached and the pipe has filled to the surface level, tug slightly on the rope as the unit is raised. * This sets the check valve, trapping the mixture inside. *. When the unit has been raised clear of the liquid, the amount of solids in the sample can be read using the 1 ft. (0.31 m) increments marked on the pipe sections. * To release the material in the unit, touch the pin extending from the bottom section against a hard surface. * This opens the check valve to drain the sample.